• RMG 290ES Sail Winch

Standard 290 size winch for up to 10R and similar classes.

Comes with 32s drum unless otherwise specified.


Summary of Features 

  • Description
  • Drums
  • Microcontroller
  • Dynamic Pulse Width Modulation
  • Stall protection
  • Low Battery Monitoring
  • Low Battery Failsafe
  • Scaled Linear Travel
  • Input Deadband
  • Voltage Protection
  • Overrun Protection
  • Power supply from 4, 5 or 6 cells (4.8 to 7.2 Volts)
  • Integral 5 Volt regulator for single battery operation
  • Wide travel range
  • Ball bearing on output shaft
Standard Equipment

  • Hitec/JR servo lead
  • 300mm power supply flying leads
  • Double spool drum including M3 screw and washer. Default size 26mm (280), 32mm (380)
  • 2 x M3 s/s pan head winch mounting screws
  • SmartWinch User Guide
  • 12 months warranty
  • Free Technical Support

Description


290EF High speed for up to IOM and similar size boats. 
290ES Moderate speed and torque for IOM, Marblehead, R10R etc. 
290EL Higher torque and longer travel version of the 280ES for EC12 and similar size.
380ES Powered by a Mabuchi RS380 motor. By its physical size and shear grunt this is primarily a big boat winch. Ideal for classes such as the A, AC etc. However it should be noted that it is possible (but very rare) to have the Acetal gears on the this model to fail under shock load stall situations. 
 
Drums
Three standard diameters, 42mm, 32mm, 26mm in standard and wide configurations are available to suit each model and various sheeting system configurations. There are also 3 sizes of Z shaped tapered spiral drums and 3 self tensioning drums
 
Microcontroller
What makes this winch smart is it's state of the art digital electronics controller. The controller is based on a Microcontroller Unit (MCU) which is a very small computer system in one chip. The MCU is controlled by a software program (ROM) which monitors all aspects of the winch's operation. Included in this program are some 'smart' fail-safe features that can protect the winch from problems that may occur with your yacht's electrics or sheeting system. To fit all the features into the controller, surface mount technology is used on a double sided printed circuit board.

Dynamic Pulse Width Modulation
Servo systems use Pulse Width Modulation (PWM) to reduce power and speed as the desired position is approached. This gives finer and smoother control when small movements are required. But the problem with standard P.W.M. is that as the desired position is approached, the reduction in power can cause the servo to stop short. This can result in excess power consumption and. This is what's happening when a servo is not moving but is buzzing. However, unlike other winches and servos the SmartWinch has dynamic PWM. If the SmartWinch controller detects that it has not reached the desired position, power is increased up to 100% if necessary until the desired position is reached.

Stall Protection
When a conventional servo becomes stalled, it will stay stalled until the problem is solved. If not solved in time, the battery can be flattened, motor overheated, output transistors overheated and possibly damaged. But the SmartWinch knows when it is stalled and can protect itself by shutting down. The SmartWinch then signals that it is stalled by sounding a two-tone beep at 2 second intervals until reset. Stall mode can reset by moving the Tx stick in the opposite direction. If this does not work, turn the SmartWinch off and on again.

Battery Testing
The SmartWinch can monitor the battery for low voltage. If the voltage is below the warning level a warning signal (5 rising tones) will sound when the winch is switched on. If, during normal operation the voltage falls below the shutdown level, the winch will drive to the low battery failsafe position and hold there until the battery is replaced or voltage recovers. See Table 1. Default is battery monitoring OFF.
 
Low Battery Failsafe Position
The default low battery failsafe position is booms half out. But this is only true if using a standard spool type drum. If a spiral drum is used then this position would be closer to full in and could make it difficult to get the boat ashore. To compensate for this the low battery failsafe position is also adjustable so you can choose whatever position you wish between full in and full out.
 
Scaled Linear Travel
Travel response to the first 25% of Tx stick movement from full in when single ended or both ends when double ended is adjustable from 1:1 at minimum to a maximum of 4:1. For example, if 50% is selected, each increment of the first 25% of the stick range results in half the travel of the default setting. This feature is similar to exponential adjustment in a computer Tx. However scaled linear has the advantage of consistent incremental travel over the first 25% of stick movement whereas exponential is constantly varying. Default is 1:1.
 
Input Deadband
Input deadband is the amount dithering in the Rx signal that a servo can tolerate without responding to by constantly jittering. This is adjustable from 0.8 to 10 microseconds. Deadband adjustment allows the optimization of TX fine trim control. The default setting is 5 microseconds.
 
Voltage Protection
For protection of the electronics from over or under voltage conditions the circuit will disable itself when the supply voltage goes above 9 Volts or below 3.8 Volts.
 
Overrun Protection
Once set up to suit the transmitter, the winch is programmed to ignore signals which are above maximum and below minimum pulse width of that transmitter. This means that should interference cause the receiver to send signals outside the normal range for that transmitter, the winch will just ignore those signals. It will not try to travel closer than close hauled or beyond square running positions.

Electrical Specifications 6V (7.4V)
Idle Current (mAmps) 23
No Load Current (Amps) 1.5
Stall Current (Amps) 19 (23.4)
Max Voltage (volts) 9
Min Voltage (volts) 3.8
Mechanical Specifications (metric) 6V (7.4V)
Max Output Power (watts) 18.1 (27.3)
No Load Speed (revs/sec) 5.1 (6.3)
No Load Line Speed (sec/300mm) 0.59 (0.48)
Stall Torque (kg.cm) 23.4 (28.8)
Drum diam (std) (mm) 32S
Max Revolutions (revs) 5
Max Travel (mm) 500
Resolution (mm) 0.41
Accuracy (mm) +/- 1
Dimensions (mm) 73 x 56 x 54
Weight (gm) 140

RMG 290ES Sail Winch

  • Brand: RMG SailWinch
  • Product Code: 290ES
  • Availability: In Stock
  • $284.50


Related Products

26mm Standard Winch Drum

26mm Standard Winch Drum

26mm Standard Winch Drum..

$8.80

32mm Standard Winch Drum

32mm Standard Winch Drum

32mm Standard Winch Drum    ..

$10.45

42mm Standard Winch Drum

42mm Standard Winch Drum

42mm Standard Winch Drum    ..

$13.20

RMGSwitch Std

RMGSwitch Std

Features and SpecificationsSuper Low Profile.Simple to install. Requires only one 20mm diameter hole..

$37.90

Self Tensioning  Drum 32L (32mm dia left)

Self Tensioning Drum 32L (32mm dia left)

IntroductionThe RMG self tensioning drums allow for the elimination of tensioning devices in the she..

$23.65

Self Tensioning  Drum 32R (32mm dia right)

Self Tensioning Drum 32R (32mm dia right)

IntroductionThe RMG self tensioning drums allow for the elimination of tensioning devices in the she..

$23.65

Self Tensioning  Drum 42L (42mm dia left)

Self Tensioning Drum 42L (42mm dia left)

IntroductionThe RMG self tensioning drums allow for the elimination of tensioning devices in the she..

$26.40

Self Tensioning  Drum 42R (42mm dia right)

Self Tensioning Drum 42R (42mm dia right)

IntroductionThe RMG self tensioning drums allow for the elimination of tensioning devices in the she..

$26.40

Tags: winch